How to Replace a Kia Sportage Replacement Key

The key on many Kia Picanto Key Fob Replacement models has an entry system that is keyless in. The key can be compared to a remote control and can be exchanged with a brand new one from an kia soul key fob dealer or a locksmith.

Key fobs may stop working due to a variety of reasons, including a dead coin battery worn buttons water damage, signal interference and a malfunctioning receiver module. Here are some helpful tips on how to get your Kia Sportage replacement key to function again.

How to replace the remote key or smart key

If your kia duplicate key comes with an intelligent key, remote key push to start key or a regular non-transponder metal key the battery in these keys will eventually require replacing. This is especially relevant if your car displays a message indicating that the smart or remote key has low battery power.

It's a simple process. In order to replace the key fob battery remove the mechanical key from the slit at the back of the key fob. Next, break the cover. Inside the key fob will be tiny screws that hold the battery in its place. Take out the old battery by detaching the screw with a small screwdriver. Then, insert the new and close the slit in the key fob.

Test the key fob by pressing the lock/unlock buttons. It's good when the doors lock or unlock as you expect. You can now take advantage of the 2011 kia optima key fob's hands-free lock/unlock feature when your fingers start to get cold or you have to run some errands in Brandon.

Note: Certain key fobs may need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or automotive locksmith can access. Other keys (non transponder keys made of steel), do not need programming. If you need to reprogramme your key, you'll need to record the key code number on the tag for the key code.

How do I replace a battery

If the Kia key fob does not respond when you press the lock/unlock button, it's likely that the battery is not fully charged. A low battery may cause other issues, such as the check engine light turning on or the engine not working correctly. It is quite simple to replace key fob batteries by using only two tools.

Be sure to turn off your vehicle and close all doors before you begin. Locate the small plastic piece on the bottom of your key fob, and play with it until a metallic key slips out. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob's battery, take off the cover at the rear and use a pry bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery, and then place the new battery in a way that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid damaging or breaking the metal contacts.

After installing the new battery then turn the key fob off and on in the ignition until the door locks up. You can then test the kia forte replacement key's key fob once more to ensure it's working properly.

How to replace the smart key

You may have either an ordinary keyfob or Smart Key, based on the model of Kia Sportage. The difference between them is that the smart key is equipped with an incredibly small key blade tucked inside it, while the standard key fob does not. Both kinds of key fobs come with batteries that will eventually need to be replaced. Fortunately, this is an easy process that only takes about two minutes.

Before you start it is important to ensure that you are on a level surface with sufficient lighting and that your Kia is off. Keep in mind that the fob can contain small pieces that could fall when you're not careful.

The first step is to locate the small release button that is located on the lower backside of your fob. It can be a circular silver button or a rectangular slot. Once you press this button, the mechanical blade will pop out and you can then open the key fob.

After the key fob has been opened, remove the old battery. The new battery is a one called CR-2032 and can be bought through the internet or at a local auto parts store. After installation with the battery, you should be able to lock or unlock your vehicle using your key fob, even if your engine isn't running!

How do I replace a mechanical key

The Kia keyfob is a wonderful convenience, allowing us to lock or unlock our car by simply pressing a button. Like any other device it may have issues occasionally. There are ways to fix these problems and keep your key fobs working for a long time.

One of the most frequently encountered problems is a low or dead battery. This can cause the fob to stop working completely or stop working at times. If this is the case try replacing the battery with a fresh new one.

If this does not solve the issue, try using the flathead screwdriver that is standard to push the plastic casing of the fob open. Be careful not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a new one.

Close and open the door with the mechanical key. (Every Kia fob comes with an emergency mechanical key that fits into the slot). Test the fob to make sure it's working properly. Contact a dealer or locksmith to fix the issue in the event that the fob is not working. Make sure they make you an emergency key that works in all the trunk and door cylinders in order to prevent lockouts in the future.